I-PAC 2 Arcade EncoderUltimarc
32 Inputs plus trackball and spinner connector/PAC-Link expansion)
Now supports power control, mouse and volume buttons!
- I-PAC The world's most advanced PC interface for buttons and joysticks.
(Click Here For Wiring Diagram)
- Full Speed USB 2.0. 32 or 56 Inputs. Upgrade-able firmware.
- The ONLY keyboard encoder to have up to 56 inputs each with it's own dedicated microprocessor pin. No interaction or delays, vital for multi-button games such as fighting games.
- Is much more than a keyboard encoder! Pins can be configured as mouse buttons or game controller buttons, plus power and volume control.
- The ONLY keyboard encoder which emulates a USB keyboard and yet breaks through the USB simultaneously-pressed-switch limit of 6 switches (plus ctrl,alt,shift) which afflicts all USB keyboard devices. This is beacuse it has inbuilt full native USB support, and does not rely on an add-on adaptor.
- The ONLY device to have a shift function which allows ANY input to be assigned to a shifted secondary keycode and the shift button can have it's own function too so no need for a dedicated extra control panel button.
- The ONLY device to have a self-test LED which not only gives an instant visible check of your installation but also can indicate which connection (if any) is causing a problem.
- Retains it's programming after power off. Beware! Not all keyboard encoders do this!
The I-PAC (Interface for Pc to Arcade Controls) are a range of boards which allow connection of arcade controls such as buttons and joysticks to a keyboard port or USB port on a PC motherboard. It was designed around the MAME emulator which supports over 1000 arcade games and can be used with other emulators or any software which requires keyboard or game controller input.
It is designed to be used inside an Arcade Games cabinet with the PC motherboard also mounted inside, but could just as easily be used with simply a control panel without a cabinet.
Special shift function buttons mean that a normal keyboard is only be needed for game loading and configuration, not for game play. All key codes can be programmed but you don't have to as you can use the built-in default configuration which has all standard MAME codes for quick and easy installation. Programmed keys codes are stored even after power off.
The I-PAC2 has 32 inputs. They are all programmable and are marked as 2 joysticks, 8 buttons each, plus coin1, coin2, start1, start2 and Mame control keys. Any inputs can be assigned as a shift key to access an alternate code set. This board also has a connector which can be configured to plug our trackball and spinner into, or for our console interfaces.
The MAME control keys are by default assigned to the "A" and "B" inputs. Check out the code table here for all default assignments.
The I-PAC4 has 56 inputs. All programmable and marked as 4 joysticks, 8 buttons each plus coin 1,2,3,4 and start 1,2,3,4. Any inputs can be assigned as a shift key to access separate codes sets.
- Fully programmable key code set. Stored even after power off unlike some other interfaces which lose all data when powered off.
- Controls can be assigned to any key code, game controller button, plus mouse buttons, power, sleep or wake.
- All joystick/button connections easily made via screw tag strip. Connections marked on the board.
- Chunky 5mm screw connectors .
- Self-Test LED gives an instant check of all your wiring. Can indicate which, if any, input has a problem.
- All button inputs referenced to ground - no need to re-wire separate grounds to each button.
- Lead plugs into USB port.
- Using host software, an unlimited number of key code configurations can be stored and downloaded on-the-fly. Retained on power off.
- No separate power needed
- Does not use a matrix - no ghost keys.
- Does not use a scanning method which causes a variable delay. Each input has it's own dedicated connection into the on-board CPU .
- Fast running interrupt-driven software gives much better response than a standard keyboard controller. Key debounce uses a state method for each key. No delays between keys depressed at the same time. (essential for fighting games).
- Either uses standard MAME keys or you can program your own character set.
- Shift functions. Holding "Start1" and pressing other buttons sends a range of codes for MAME functions such as "escape", "Coin 1", "tab", "enter". This means no extra buttons are needed on the cabinet. In programmable mode any input can be the shift key and all keys can be programmed with a shifted code.
- Special note for Windows MAME users! Shift key functions mean you can select and start games from the Windows interface without using the keyboard or mouse.
- No special drivers needed. USB drivers are generic Windows.
- Fully compatible with all Apple Macs which have USB ports.
- Supports the Apple Mac "command" key and the Windows "GUI" keys.
- I-PAC4 and I-PAC2 boards and J-PAC can be paired in any combination to increase the total number of inputs.
- Key code programming is integrated directly into many popular front ends for seamless launch of emulator or other applications which require different codesets.
- The I-PAC uses a high-performance micro-controller chip . No matrix or diodes are used hence absolutely no ghosting, blocking or delays.
- De-bounce. This uses a state counter method. Each input has it's own counter. This means simultaneous key presses are never locked out.
- Key code flash ROM storage. Retains custom settings after power off/on (excluding I-PAC VE)
- Full-speed USB 2.0 compatible.
- Shift key logic including protection against stuck keys.
Sold Separately: I-PAC 2 Wiring Harness (26.99 CAD)
A complete set of wires and ground harnesses to wire your two player arcade using the I-PAC 2 arcade encoder.
Twelve signal wires for player action buttons, two signal wires for player one and two start buttons, one signal wire for coin in button, eight signal wires for joysticks and one ground harness.
- 25 - 1 meter 24 AWG wire with a female .187" crimped end.
- 1 - Insulated Ground Harnesse.